How do you wire a Motorguide trolling motor?

Loosen the two terminals on the circuit breaker supplied with the trolling motor. Slide the red wire from the motor over one of the terminals and tighten it down. Loosen the positive terminal on the second battery. Slide the red wire over the positive terminal on the second battery and tighten it down.

How do you wire a trolling motor?

The circuit breaker should be linked directly to your trolling motor, connecting the positive (red) lead from the motor to the positive terminal on the circuit breaker. The circuit breaker should then be connected to your first battery from its negative terminal to the positive terminal on the battery.

What gauge wire is needed for a trolling motor?

6 gauge

How do you wire a 12 volt trolling motor?

12-Volt Motors

  1. Link the red wire from the power cable of the trolling motor to the positive terminal of the battery. Employ a 50-amp circuit breaker with this connection.
  2. Connect the black wire from the power cable of the trolling motor to the negative terminal of the battery.
IT IS INTERESTING:  How do you determine if a motor is overloaded?

Why does my trolling motor plug have 3 wires?

The three wires are for a trolling motor that will operate on either 12 volts or 24 volts. 12/24 volt motors have a switch to choose which you want. Thus the third wire to send power to the 24 volt side of the switch.

How many amps does a 70 pound thrust trolling motor draw?

How many amps does a trolling motor draw?Motor Thrust / ModelMax Amp DrawCircuit Breaker70 lb.4250 Amp @ 24 VDC80 lb.5660 Amp @ 24 VDC101 lb.4650 Amp @ 36 VDC

What size battery do I need for a 30 lb thrust trolling motor?

12 V

What size battery do I need for a trolling motor?

Most trolling motor batteries fail due to lack of proper charging. We suggest selecting a 12 volt deep cycle marine battery with at least a 110 amp hour rating, usually a group 27 size battery. The higher the amp hour rating, the more run time you will receive.

How many amps does a 36 volt trolling motor pull?

A batteries specs always state that there is something like 210 reserve minutes at 25 amps.

Can you mount a trolling motor on the side of a boat?

Unless, you have a very good reason – mount it on the port or left side of the boat. i.e. the opposite side – of the boat from the driver. REW-I have a Pinpoint trolling motor, so the electrical on the motor is always in the same place whether up or down.

How much does it cost to have a trolling motor installed?

You can spend around $4000 on an electric trolling motor system. The cost of an electric trolling motor system can vary widely, but if you have a medium sized boat and want a trolling motor that has high performance, you’re going to be spending around $4,000 to get all the pieces you will need.

IT IS INTERESTING:  What does an ECM motor do?

Can you put a trolling motor on a bowrider?

Trolling motors are best used on your bowrider as a way to quietly move along a shoreline, navigate a quiet bend in the river, or circle an underwater feature while casting.

Can you use a 24v trolling motor on 12v?

For a cable steer or hand controlled model this will not hurt the motor, but it will considerably affect the performance of the motor. … However, an electric steer motor, such as, the PowerDrive, Terrova, or Ulterra cannot be used on lower voltages.

What is the difference between a 12v and 24v trolling motor?

A 12-volt trolling motor is the most inexpensive and easiest to run. It does, however, lack the staying power and thrust that the other two provide. A 24- or 36-volt system will allow the angler to fish longer periods out on the water, as they draw lower amps while providing increased thrust for more power.

Can I run a 12 volt trolling motor on 24 volts?

To answer your base question – can I convert my 12 volt trolling motor to 24 volts – to give me more power or thrust?? The answer is NO. Essentially, you have a 12 volt motor. If you try to run it on 24 volts, you will burn it up.

Motors