Why stator is used in induction motor?

The stator of an induction motor consists of poles carrying supply current to induce a magnetic field that penetrates the rotor. To optimize the distribution of the magnetic field, windings are distributed in slots around the stator, with the magnetic field having the same number of north and south poles.

Why stator is used in motor?

In an electric motor, the stator provides a rotating magnetic field that drives the rotating armature; in a generator, the stator converts the rotating magnetic field to electric current. In fluid powered devices, the stator guides the flow of fluid to or from the rotating part of the system.

Why starters are used in induction motor?

The three phase induction motors are self-starting due to rotating magnetic field. But the motors show tendency to draw very high current at the time of starting. … Hence there should be a device which can limit such high starting current. Such a device which limits high starting current is called a starter.11 мая 2017 г.

IT IS INTERESTING:  Are electric car motors brushless?

What is stator and rotor of induction motor?

The stator is in the stationary electrical component. … The rotor is the rotating electrical component. It also consists of a group of electro-magnets arranged around a cylinder, with the poles facing toward the stator poles. The rotor is located inside the stator and is mounted on the AC motor’s shaft.

Where are induction motors used?

Used in almost every process, induction motors are mainly used in water pumps, kitchen appliances, fans and air conditioners, automobiles and common industrial machinery like boiler pumps and compressors.

Does a stator produce AC or DC?

The stator is the coil of wire housed inside the engine case. A magnet on a shaft spins within the stator, creating alternating current (AC). That current travels along fairly heavy gauge wire through the case and into the rectifier/regulator which converts it to DC power, and at a consistent output.

What is a motor stator made of?

The stator frame consists of laminations of silicon steel, usually with a thickness of about 0.5 millimetre. Lamination is necessary since a voltage is induced along the axial length of the steel as well as in the stator conductors. The laminations are insulated from each other usually by a varnish layer.

What are 3 types of motor controls?

There are mainly there are three types of motor control circuits:

  • Direct On Line Starter (DOL starter)
  • Star Delta Starter.
  • Auto Transformer Starter.

What is the full form of DOL starter?

A direct on line (DOL) or across the line starter applies the full line voltage to the motor terminals. This is the simplest type of motor starter. A DOL motor starter also contains protection devices, and in some cases, condition monitoring.

IT IS INTERESTING:  Best answer: How often should you grease electric motors?

Which starting method is best for induction motor?

Starting of an Induction Motor

  • Direct on line starter. The direct on line starter method, of an induction motor is simple and economical. …
  • Star delta starter. The star delta starter method of starting three phase induction motors is very common and widely used among all the methods. …
  • Auto transformer starter.

Is armature and rotor same?

The armature is the winding to which the load is connected. In small generators, the field windings are often on the stator, and the armature windings are on the rotor. Most large machines, however, have a rotating field and a stationary armature. … Thus, the armature is the stator and the field is the rotor.

What are the types of motor winding?

Types of Motor Windings

  • Stator Winding. The slot on stator core of the three-phase motor winding carries stator winding. …
  • Rotor Winding. In a motor, the rotating part is known as the rotor. …
  • Lap Winding. Lap winding is the one kind of armature winding. …
  • Wave Winding.

What is the stator in a DC motor?

The stator is the stationary part of a motor, while the armature rotates. In a DC motor, the stator provides a rotating magnetic field that drives the armature to rotate.

Which motor is used in fan?

induction motor

Which type of winding is induction motor?

The most used winding type for medium-size induction motors is a double layer winding with pitched winding step, for example pitched for two stator slots (Fig. 2). Significant advantage of the aforementioned winding is a smaller mass of inserted copper because of shortest winding-ends.

IT IS INTERESTING:  How much electricity does a gate motor use?

What are the advantages of induction motor?

Induction Motor Advantages:

  • Induction motors are simple and rugged in construction. …
  • Induction motors are cheaper in cost due to the absence of brushes, commutators, and slip rings.
  • They are maintenance free motors unlike dc motors and synchronous motors due to the absence of brushes, commutators and slip rings.
Motors