Electric motors require lubricants with specific characteristics. Use of the wrong grease often leads to early electric motor failures. The grease consistency preferred for electric motors is normally NLGI 2 or 3, with a base oil viscosity of 100-150 cSt @ 40°C.
Can you lubricate an electric motor?
Electric-motor lubrication is not complicated. You simply need to select the correct lubricant, apply the right amount each time, and do so at the required frequency.
What kind of lubricant is used for electric motors?
A NLGI 2 grade grease is the most commonly used in electric motor applications. ASTM D 3336 oxidation life. require a grease with an EP additive. Dropping Point: The dropping point gives an indication of the temperature at which the grease will melt or the oil will separate from the thickener.
Do bearings need lubrication?
Lubrication is absolutely essential to the proper operation of ball and roller bearings. A proper lubricant will reduce friction between the internal sliding surfaces of the bearings components and reduce or prevent metal-to-metal contact of the rolling elements with their raceways.
How do you lubricate a small electric motor?
Electric Motor Bearing Lubrication Procedure
- Ensure the grease gun contains the appropriate lubricant.
- Clean the areas around the relief and fill fittings.
- Remove the grease relief valve or drain plug.
- Grease the bearing with a calculated amount of grease. …
- Watch for grease coming out the relief port.
Can I use wd40 on an electric motor?
Yes, WD-40 is safe to use on electronics. It is used frequently to dry out auto ignition systems as it it non-conductive, displaces water, and lubricates the parts without getting sticky. I also use it to clean up and dry out computers and power supplies.
How do you lubricate an electric fan motor?
- Remove the front grill of the fan.
- Lay the fan down on a flat surface with the exposed face up. …
- Apply a light nondetergent household oil that is SAE20. …
- Spray the shaft carefully with lightweight lubricant. …
- Reassemble the fan and test.
- Remove the front blade guard by prying off the clips or removing the screws.
How often should an electric motor be greased?
When the operating temperature is between 80°C – 100°C (176°F – 212°F), oil should be replaced at least every three months. For critical equipment, it is advisable that lubricating oil be analyzed at least every three months to determine when oil replacement is necessary.
How do you maintain an electric motor?
7 Ways to Ensure Better Maintenance of Electric Motors
- Perform Visual Inspections. A quick visual inspection can reveal some important details about the electric motor. …
- Perform a Brush and Commutator Inspection. …
- Conduct a Motor Winding Test. …
- Check the Bearings. …
- Perform Vibration Tests. …
- Use Infrared Thermography in Predictive Maintenance. …
- Document Everything.
What is the best lubricant for bearings?
Bearings in some applications use oil, but grease is the lubricant of choice for 80 to 90% of bearings. Grease consists of about 85% mineral or synthetic oil with thickeners rounding out the rest of the grease volume.
Can I use wd40 on bearings?
It’s important to use a silicone-based lubricant. WD40 or others like it will dry out your bearings and attract dust and dirt. … It doesn’t take much, and the excess will just spin out when you replace your shields, pop your bearings back in your wheels and start shredding. Skate safe and enjoy your new-found speed.”
Which bearing does not require lubrication?
Due to this, self-lubricating bearings are also referred to as maintenance-free or greaseless bearings as they require no relubrication or grease. An example of a self-lubricating bearing is our GGB-CSM® greaseless bearing.
Can electric motors be repaired?
If an electric motor operates at too high a voltage, excess current flowing through the windings can cause them to become hot and burn out. While it is normally not practical to repair small, direct current (DC) motors that have burned out, other motors can be repaired by rewinding.
Can a bearing be over greased?
Too much grease builds pressure, pushing the rolling elements through the fluid film and against the outer race. The bearing now has to work much harder to push the rolling elements through a mud bog of grease. The increased friction and pressure from too much grease raises the temperature inside the bearing.19 мая 2016 г.